Radiator Fan Keeps Running? Causes, Sensor and Relay Failures, A/C Pressure Problems, and Repair Costs

Table of Contents

Radiator Fan Keeps Running?

You turn off your car, grab your keys, and start walking away. Then you hear something unusual.

A loud fan is still running under the hood.

At first, you assume the engine is simply cooling down. But several minutes later, the noise hasn’t stopped. Now you’re wondering whether something is wrong with the cooling system—or whether the fan is going to drain your battery overnight.

It is a surprisingly common concern, and the answer isn’t always straightforward.

In October 2013, General Motors issued Service Bulletin PI1069 addressing cooling fans that either continued running with the ignition off or failed to operate on certain Chevrolet Impala police vehicles.

The possible causes included sticking fan relays and cooling fan motors drawing excessive electrical current.

A separate Ford service program later documented high-speed cooling fan relay failures in certain 2016–2018 Explorer vehicles. These failures could leave the fan running continuously, damage electrical terminals, and eventually drain the battery.

But electrical relays aren’t the only explanation.

Mercedes-Benz also documented cases where radiator fans immediately ran at full speed because of engine control software behavior associated with coolant temperature readings.

Three different situations. Similar symptoms. Very different repairs.

That is why replacing the radiator fan without understanding the reason it is running can become an expensive mistake.

In this guide, we’ll examine how radiator cooling fans work, why they sometimes continue operating after shutdown, and how coolant temperature sensors, relays, A/C refrigerant pressure sensors, electronic control modules, and actual engine overheating contribute to the problem.

We’ll also look at real manufacturer service cases, OBD-II diagnostic trouble codes, troubleshooting steps, and the factors that determine repair costs.


Why Does My Radiator Fan Keep Running?

Your radiator fan is an essential part of the engine’s thermal management system.

While driving at highway speeds, air naturally flows through the front grille and across the radiator. This airflow helps remove heat from the coolant circulating through the engine.

At low speeds or while sitting in traffic, however, natural airflow becomes insufficient.

That’s when the radiator cooling fan takes over.

Most modern passenger vehicles use one or more electric cooling fans. Unlike older mechanically driven fans, electric fans can operate independently of engine speed.

Some can even run after the ignition has been switched off.

The important question is whether the fan is operating because the vehicle needs additional cooling or because a component has failed.

Common Symptoms and Their Possible Causes

SymptomPossible CauseWhat to Check
Fan runs at full speed immediately after a cold startCoolant temperature sensor or fail-safe strategyECT live data and wiring
Fan continues running after engine shutdownNormal after-run cooling or stuck relayDuration and relay operation
Fan runs faster when A/C is onNormal condenser cooling or elevated refrigerant pressureA/C pressure data
Fan runs at maximum speed with normal dashboard temperatureSensor disagreement or control issuePCM commands and scan data
Fan runs constantly while engine overheatsCooling system malfunctionCoolant level, thermostat, radiator
Fan keeps running until battery diesRelay or fan control module failurePower supply and relay terminals
Fan is unusually loud or vibratesFan motor, bearing, or blade damageFan assembly condition

One symptom alone rarely identifies the failed component.

The most useful diagnostic clue is whether the fan is following a legitimate command from the vehicle’s computer.


How the Radiator Cooling Fan Control System Works

Modern cooling fans are controlled by more than a simple temperature switch.

The Engine Control Module (ECM) or Powertrain Control Module (PCM) evaluates several operating conditions before deciding when the fan should run.

Depending on the vehicle, those inputs can include:

  • Engine Coolant Temperature (ECT)
  • Cylinder Head Temperature (CHT)
  • A/C Refrigerant Pressure
  • Air Conditioning Request
  • Vehicle Speed
  • Ambient Air Temperature
  • Transmission Temperature
  • Additional thermal management requests

When the engine reaches a manufacturer-defined temperature threshold, the computer may activate the fan.

If cooling demand increases, the system can command a higher fan speed.

Many newer vehicles use Pulse Width Modulation (PWM) instead of basic on/off control.

PWM allows the system to vary fan speed electronically by controlling the duty cycle of the command signal.

In practical terms, the fan doesn’t always need to run at maximum speed.

It can adjust its output to match the cooling demand.

This improves temperature control and reduces unnecessary electrical load.

However, if the computer receives incorrect information—or the fan control hardware fails—the fan may operate at an unexpected speed.

Understanding that distinction is the foundation of proper diagnosis.


Is It Normal for a Cooling Fan to Run After Turning Off the Engine?

Yes. Under certain conditions, continued fan operation is completely normal.

Although combustion stops when you shut off the engine, the engine block, cylinder head, turbocharger, and surrounding components may still contain substantial heat.

Some vehicles use an after-run cooling strategy to manage this residual heat.

Ford’s owner documentation, for example, explains that the engine cooling fan may continue operating for several minutes after shutdown under certain conditions.

This behavior can occur after demanding driving conditions, but it isn’t limited to extremely hot weather.

Modern thermal management strategies may also operate based on conditions that aren’t obvious from the dashboard temperature gauge.

What About Diesel Vehicles?

Diesel vehicles equipped with a Diesel Particulate Filter (DPF) may experience additional cooling activity associated with exhaust system regeneration.

During regeneration, elevated exhaust temperatures help burn accumulated soot from the filter.

Depending on the vehicle’s control strategy, the cooling fan may continue running afterward to manage residual heat.

This does not automatically indicate a malfunction.

However, there is no universal rule that says every cooling fan must stop after exactly five or ten minutes.

Operating time varies by manufacturer, engine design, and cooling strategy.

If your fan repeatedly runs far beyond the behavior described in your owner’s manual, operates with a completely cold engine, or drains the battery, further investigation is justified.


Cause 1: A Faulty Engine Coolant Temperature Sensor

One of the first components worth checking is the Engine Coolant Temperature sensor, commonly called the ECT sensor.

This sensor monitors coolant temperature and sends information to the engine computer.

Most conventional ECT sensors use a Negative Temperature Coefficient (NTC) thermistor.

Its electrical resistance decreases as temperature increases.

The PCM interprets the sensor’s electrical signal to determine coolant temperature.

Why a Bad Sensor Can Make the Fan Run at Full Speed

Imagine starting your car on a cool morning.

The engine is cold, but the radiator fan immediately begins roaring at maximum speed.

Why would the computer request maximum cooling before the engine has warmed up?

One explanation is fail-safe operation.

If an ECT sensor circuit becomes disconnected, shorted, or unreliable, the computer may be unable to determine the engine’s actual temperature.

Rather than risk overheating, certain manufacturers program the cooling fan to operate at high speed as a protective measure.

This is often described as a fail-safe strategy.

The fan itself may be functioning perfectly.

The problem is that the computer no longer trusts the temperature information it receives.

Not every vehicle responds identically, however. Some fault conditions trigger different protective strategies.

How Technicians Diagnose an ECT Sensor Problem

A technician typically begins with a scan tool rather than replacing the sensor immediately.

With a fully cold engine, the reported coolant temperature should generally be reasonably close to the surrounding ambient temperature, allowing for vehicle-specific conditions.

If the scan tool displays an implausible reading, the technician investigates the sensor circuit.

Possible problems include damaged wiring, corrosion inside the connector, a poor ground, or sensor failure.

The technician may also compare readings from multiple temperature sensors when available.

One important detail is that a dashboard temperature gauge may not display every small temperature change.

Some manufacturers deliberately smooth the gauge response to prevent unnecessary movement during normal operation.

For this reason, live scan-tool data is usually more informative than the dashboard needle alone.


Cause 2: A Stuck Radiator Fan Relay

Cooling fan relays act as electrically controlled switches.

In vehicles using conventional relay-controlled fans, the ECM or PCM activates a relay that supplies electrical power to the fan motor.

Over time, electrical loads and repeated switching can damage the relay’s internal contacts.

If those contacts stick together, power may continue flowing even after the control circuit requests the fan to stop.

In a vehicle whose circuit allows power with the ignition off, that can leave the radiator fan running after shutdown.

Real Service Case: Chevrolet Impala Cooling Fan Relay Failure

General Motors Service Bulletin PI1069 addressed certain 2012–2013 Chevrolet Impala police vehicles and 2014 Impala Limited police vehicles.

The bulletin identified two important possibilities: sticking cooling fan relays and fan motors drawing excessive current.

Why does motor current matter?

An electric motor that is binding, worn, or otherwise malfunctioning may draw more current than intended.

Excessive current can damage relay contacts and electrical connections.

GM instructed technicians to inspect the relays for discoloration or distortion, examine the accessory wiring block, and measure fan motor current draw.

For the vehicles covered by that specific bulletin, GM provided a current-test procedure and replacement criteria.

Those numerical limits should not be applied automatically to unrelated vehicles.

The lesson is broader than a single Chevrolet model.

A failed relay may be the visible symptom of a failing fan motor, rather than the original problem.

Replacing only the relay could leave the underlying electrical issue unresolved.

Real Service Case: Ford Explorer Battery Drain

Ford’s Customer Satisfaction Program 21N01 addressed high-speed cooling fan relay issues on certain 2016–2018 Explorer vehicles.

According to Ford, prolonged idling could contribute to relay failure.

The fan might then remain on continuously or fail to activate at all.

An overheating relay connection could damage terminals and potentially lead to electrical arcing.

Owners might experience a dead battery, damaged relay components, or engine overheating if the fan stopped working.

Ford developed a repair procedure involving the affected terminals and relay configuration.

This example demonstrates why a continuously running fan should not always be dismissed as a minor annoyance.

The electrical connections themselves may need inspection.

For U.S. vehicle owners, it is also worth checking whether the vehicle has an applicable manufacturer service program, warranty extension, or recall.

A Technical Service Bulletin (TSB) is not automatically a safety recall, and coverage depends on the vehicle identification number and the terms of the specific program.


Kori’s Midway Thoughts: The Fan May Be Doing Exactly What It Was Told

The more I look at cooling fan failures, the more I realize that the sound of a spinning fan tells us very little about the actual problem.

A fan running at full speed could be protecting an overheated engine, responding to a faulty temperature signal, or receiving power through a relay that refuses to open.

Those situations may look identical to the driver, yet require completely different repairs.

I’ve come to believe that the smartest automotive repair is not the one that replaces a suspicious part first. It’s the one that identifies where the normal control process broke down.

A few minutes spent comparing sensor readings and computer commands can sometimes prevent a much larger repair bill.

Kori’s One-Line Tip: Before replacing a cooling fan, compare the PCM’s commanded fan operation with the fan’s actual behavior and the engine’s live coolant temperature reading.


Cause 3: A/C Refrigerant Pressure Problems

The radiator fan doesn’t exist solely to cool the engine.

On many vehicles, the same fan assembly also helps cool the air-conditioning condenser.

The condenser is usually mounted near the front of the vehicle, close to the radiator.

As refrigerant passes through the A/C system, the condenser releases heat into the outside air.

When your vehicle is moving, airflow across the condenser helps remove that heat.

When you’re stopped at a traffic light on a hot summer afternoon, the electric fan becomes especially important.

That’s why the radiator fan may run even when engine coolant temperature is relatively low.

How High Refrigerant Pressure Affects Fan Speed

The A/C refrigerant pressure sensor reports pressure information to the vehicle’s control system.

As cooling demand or high-side pressure increases, the computer may command additional airflow through the condenser.

A higher fan speed can therefore be normal when air conditioning is operating under demanding conditions.

However, abnormally high refrigerant pressure may also indicate a problem.

Potential causes include refrigerant overcharging, poor condenser airflow, contamination, or restrictions within the refrigerant circuit.

A faulty pressure sensor or damaged wiring can also produce misleading information.

There is an important difference between actual high refrigerant pressure and an incorrect pressure reading.

The appropriate repair depends on which one is present.

Likewise, insufficient refrigerant does not automatically cause the fan to run continuously. Many vehicles disable the A/C compressor under certain low-pressure conditions.

Real Service Case: Mercedes-Benz C-Class W203

Automotive technology supplier HELLA published a diagnostic case involving Mercedes-Benz C-Class W203 vehicles with automatic climate control.

The reported symptoms included an A/C compressor that would not engage and radiator fans operating at full power.

HELLA identified the front Signal Acquisition Module (SAM) as a possible source of the problem.

Technicians were advised to inspect the SAM fault memory and investigate refrigerant pressure/temperature sensor circuit faults.

The lesson is that the engine computer may not always store the most relevant fault information.

Sometimes, the air-conditioning control system or another electrical module holds the critical clue.

If the cooling fan problem appears alongside poor A/C performance, both systems deserve attention.


Cause 4: Fan Control Module or Engine Computer Problems

In modern vehicles, cooling fan operation may be managed through dedicated electronic control modules.

The PCM sends a command to the fan controller, which regulates motor operation.

If the module fails internally, the fan may no longer respond correctly.

Some failures cause the fan to operate at a fixed speed.

Others prevent the fan from running when needed.

The critical diagnostic step is comparing the computer’s intended output with the electrical system’s actual behavior.

If the PCM commands maximum fan speed, the technician should investigate why that command was issued.

If the PCM commands the fan off but the fan remains powered, attention shifts toward the relay, fan controller, wiring, and power distribution circuit.

Real Service Case: Mercedes-Benz Engine Software

Mercedes-Benz technical information LI07.08-P-057165 documented radiator fans running at 100% after engine startup in vehicles equipped with certain ME9.7 engine control systems.

Diagnostic fault code 2237, related to coolant temperature sensor operation, could be stored.

The manufacturer connected the condition to software temperature-limit logic under significant differences between ambient and coolant temperatures.

The published service information specifically cautioned against unnecessary component replacement while the software-related issue was being addressed.

This is an especially useful diagnostic example.

A fault code naming a temperature sensor does not necessarily prove that the sensor hardware has failed.

Software calibration, circuit inputs, and control-system logic can all influence the outcome.


Cause 5: The Engine Is Actually Overheating

Sometimes the radiator fan is not malfunctioning at all.

It is running continuously because the cooling system cannot remove enough heat from the engine.

This situation deserves more immediate attention because ignoring genuine overheating can lead to expensive engine damage.

Low Coolant or a Coolant Leak

Insufficient coolant reduces the system’s ability to transfer heat.

Leaks may develop around the radiator, hoses, water pump, coolant reservoir, or other connections.

If the coolant level repeatedly drops, the cause should be investigated rather than simply topping it off indefinitely.

A Stuck Thermostat

The thermostat regulates coolant flow based on engine operating conditions.

If it becomes stuck closed, adequate circulation through the radiator may be restricted.

The engine can overheat even while the cooling fan operates continuously.

A thermostat stuck open usually creates a different problem, such as slow engine warm-up or difficulty maintaining normal operating temperature.

A Restricted Radiator or Failing Water Pump

A radiator can lose cooling efficiency because of internal restrictions or debris blocking external airflow.

A deteriorating water pump may also reduce coolant circulation.

In either situation, the computer may continue requesting fan operation because coolant temperature remains excessive.

The fan cannot compensate indefinitely for inadequate coolant flow or poor heat transfer.

If the temperature warning illuminates, steam appears, or the vehicle shows clear signs of overheating, pull over safely and follow the manufacturer’s emergency procedures.

Never remove a hot, pressurized coolant cap.


OBD-II Trouble Codes Related to Cooling Fan Problems

Modern vehicles can store diagnostic trouble codes when the powertrain control system detects an electrical or performance problem.

These codes are useful clues, but they are not final diagnoses.

OBD-II CodeGeneral DescriptionPotential Diagnostic Focus
P0117Engine Coolant Temperature Sensor Circuit LowSensor circuit, wiring, short
P0118Engine Coolant Temperature Sensor Circuit HighOpen circuit, wiring, sensor
P0128Coolant Thermostat PerformanceThermostat and cooling performance
P0480Cooling Fan 1 Control CircuitRelay, control wiring, fan circuit
P0481Cooling Fan 2 Control CircuitAdditional fan control circuit
P0526Fan Speed Sensor CircuitFan speed feedback, where equipped
P0532A/C Refrigerant Pressure Sensor Circuit LowA/C sensor and wiring
P0533A/C Refrigerant Pressure Sensor Circuit HighA/C sensor and wiring

Not every vehicle uses all these codes.

For example, P0118 indicates a high electrical signal in the coolant temperature sensor circuit. It does not directly mean that the engine coolant is dangerously hot.

Likewise, P0480 does not automatically mean the radiator fan motor has failed.

Freeze-frame data, live sensor readings, vehicle-specific diagnostic procedures, and electrical testing are needed to identify the cause.


How to Diagnose a Radiator Fan That Won’t Turn Off

The most efficient troubleshooting process begins with symptoms and gradually narrows down the fault.

Step 1: Record When the Fan Runs

Does the fan start immediately with a cold engine?

Does it run only when the A/C is switched on?

Does it continue after shutdown?

Does the behavior occur after long highway trips or while sitting in traffic?

These details help distinguish ordinary thermal management from abnormal operation.

Step 2: Check the Cooling System Safely

Once the engine has cooled completely, inspect the coolant reservoir level and look for obvious signs of leakage.

Check for warning lights, unusual odors, and visible steam.

Do not reach into the fan assembly or open a hot coolant system.

Step 3: Check Climate Control Operation

Turn off the climate control system using the appropriate vehicle controls and observe whether fan behavior changes.

Remember that windshield defrost modes may request air-conditioning operation on some vehicles, even when the driver has not selected the A/C button directly.

Step 4: Read OBD-II Live Data

A capable scan tool can help compare coolant temperature, refrigerant pressure, and commanded fan operation.

A basic code reader may not display every manufacturer-specific parameter.

For more complex fan-control faults, a professional scan tool with bidirectional control functions may be necessary.

Step 5: Inspect the Relay and Wiring

A technician can check relay operation, electrical terminal condition, ground connections, and power supply behavior.

Burned or discolored connectors deserve particular attention.

Electrical testing should follow the vehicle’s wiring diagrams.

Step 6: Test the Fan Motor and Controller

A technician may evaluate motor current draw, mechanical resistance, electrical signals, and the operation of any dedicated fan-control module.

Motor current specifications depend on the exact vehicle.

Excessive current can indicate a problem that may also damage relay contacts or wiring.

Step 7: Verify the Repair

After repairs, the cooling system should be tested under appropriate conditions.

That includes checking normal warm-up, A/C operation, fan speed changes, and shutdown behavior.

Clearing a trouble code alone does not prove that the underlying fault has been corrected.


What Should You Do If the Fan Keeps Running After Shutdown?

First, don’t immediately assume something catastrophic has happened.

A short period of after-run cooling may be normal.

Consult the vehicle’s owner’s manual to understand the intended behavior.

However, if the fan runs unusually long, repeatedly drains the battery, or operates at full speed with a cold engine, arrange a diagnostic inspection.

Never place your hands near an electric cooling fan simply because the ignition is off. These fans can start unexpectedly.

Also avoid removing a cooling fan fuse or relay as a permanent workaround.

Disabling the fan could leave the engine without adequate cooling during the next drive.

If overheating warnings, coolant leaks, or steam are present, the safer option is to stop driving and seek professional assistance.

Hybrid and electric vehicles require additional caution because their thermal management systems may interact with high-voltage equipment.


Radiator Cooling Fan Repair Costs in the United States

The final repair bill depends on which component has actually failed.

A simple relay replacement may involve far less labor than replacing a complete cooling fan assembly.

But the inexpensive-looking repair is not always the correct one.

If a failing fan motor is drawing excessive current, replacing only the relay may lead to another failure.

Similarly, an apparent cooling fan problem caused by a sensor circuit or control module may not require replacing the fan at all.

In the U.S., repair costs also vary with labor rates, vehicle design, OEM versus aftermarket parts, and regional shop pricing.

A dealership may charge differently from an independent repair facility, and diagnostic time may be billed separately.

Before approving a major repair, consider asking the shop these questions:

  • What test confirmed that this component failed?
  • Is the PCM commanding the fan to run?
  • Was the relay or motor current draw tested?
  • Are any related connectors or wiring damaged?
  • Is there a relevant manufacturer service bulletin or warranty program?
  • Will the repair include confirmation that fan operation returns to normal?

For vehicles with documented manufacturer service programs, eligibility should be checked using the VIN and current program terms.

A service bulletin alone does not guarantee free repairs.

Why Delaying Diagnosis Can Become Expensive

The most serious cost risk is not necessarily the cooling fan assembly itself.

A fan that cannot operate when needed may allow the engine to overheat.

A fan that runs continuously because of an electrical fault may cause battery drain or additional connector damage.

Meanwhile, an engine overheating because of coolant loss or restricted circulation can suffer substantial mechanical damage if the vehicle continues to be driven.

Identifying the real cause early is generally more economical than replacing unrelated parts or waiting for a secondary failure.


How to Prevent Cooling Fan Problems

Electric cooling fans don’t normally have a fixed replacement interval like engine oil or air filters.

Still, routine cooling-system maintenance can reduce unnecessary stress on the system.

Use the coolant type specified by the vehicle manufacturer and maintain the proper coolant level.

Investigate recurring coolant loss rather than repeatedly topping off the reservoir.

Keep the radiator and A/C condenser free from significant debris that blocks airflow.

If A/C performance declines, have refrigerant pressure and system operation tested rather than adding refrigerant without diagnosis.

Pay attention to unusual fan noises, vibration, or intermittent operation.

A fan that makes grinding sounds or struggles to turn may have a mechanical problem that deserves attention before it affects electrical components.

And if the fan only behaves strangely during hot-weather traffic, don’t overlook condenser airflow and A/C system pressure.

Small observations often provide the clues that lead to an accurate diagnosis.


A radiator fan that keeps running isn’t always caused by a faulty motor or temperature sensor. Coolant circulation, radiator efficiency, thermostat operation, and engine oil lubrication all contribute to keeping an engine within its proper operating temperature range.

To understand how these systems work together, what causes overheating and low oil pressure warnings, and how preventive maintenance can help avoid expensive repairs, explore  「Engine Cooling and Lubrication Systems: Overheating and Repair Costs」 


Kori’s Thoughts: Understanding the Command Is the Key to Understanding the Failure

After examining manufacturer service bulletins and the way modern cooling systems operate, one point stands out.

A continuously running radiator fan is not a diagnosis. It is a symptom.

The most useful approach is to separate the problem into five questions.

  1. Is the operation normal? Some vehicles intentionally run their fans after engine shutdown.
  2. Is the computer receiving accurate temperature information? A faulty ECT sensor circuit may trigger protective fan operation.
  3. Is the electrical system following the computer’s command? Stuck relays and faulty controllers can keep a fan powered unexpectedly.
  4. Is the A/C system requesting additional cooling? Refrigerant pressure and condenser airflow can influence fan speed.
  5. Is the engine actually overheating? Low coolant, a failing thermostat, poor radiator performance, or inadequate circulation may keep the fan working continuously.

I’ve always thought that understanding how a system makes decisions is more useful than memorizing a list of parts that might fail.

The cooling fan is a good example.

A fan should run when cooling is needed, respond correctly to changing conditions, and shut down when the system no longer requires it.

That simple behavior depends on sensors, electronic commands, relays, wiring, and mechanical components all working together.

And that is exactly why good diagnosis matters.


Radiator Fan Keeps Running Frequently Asked Questions

Q1. Why does my radiator fan keep running after I turn off the car?

Some vehicles use after-run cooling to manage residual heat after shutdown. This can be normal for several minutes, depending on the vehicle.

However, a fan that runs excessively long or drains the battery may have a stuck relay, faulty fan control module, or an electrical control problem.

Check the owner’s manual and have the system inspected if the behavior appears abnormal.

Q2. Why is my radiator fan running at full speed when the engine is cold?

A malfunctioning coolant temperature sensor circuit can cause some vehicles to activate the fan as a protective strategy.

Incorrect A/C refrigerant pressure readings or electronic control problems may also cause unexpected high-speed fan operation.

A technician should compare live coolant temperature readings and PCM fan commands before replacing components.

Q3. Is it safe to drive with the radiator fan running constantly?

It depends on the cause.

Normal cooling demand may not indicate a problem. However, continuous operation caused by faulty electrical components requires diagnosis.

If the engine is overheating, coolant is leaking, or a temperature warning appears, do not continue driving.

The priority is determining whether the fan is responding to a genuine cooling demand or operating because the control system has failed.


Radiator Fan Keeps Running References

  1. General Motors (2013). Preliminary Information Bulletin PI1069, Cooling Fans Do Not Run or Run with Key Off. Documents sticking relays, excessive fan motor current, and related electrical damage in certain Chevrolet Impala police vehicles.
  2. Ford Motor Company (2021–2022). Customer Satisfaction Program 21N01, High-Speed Cooling Fan Motor Relay. Manufacturer service information involving certain 2016–2018 Ford Explorer vehicles, relay failure, battery discharge, and electrical terminal damage.
  3. Mercedes-Benz (2014). Technical Information LI07.08-P-057165, Engine Cooling Fan Running at 100% With No Obvious Cause. Diagnostic information involving ME9.7 engine control logic and coolant temperature-related fault code 2237.
  4. HELLA Tech World. Mercedes-Benz C-Class W203: Compressor Does Not Switch On / Radiator Fans Running at Full Power. Technical diagnostic case involving the front SAM module and refrigerant pressure/temperature sensor circuitry.
  5. HELLA Tech World. Checking the Coolant Temperature Sensor. Technical explanation of coolant temperature sensing, NTC thermistors, and related electrical diagnosis.
  6. Ford Motor Company. Owner’s Manual: Engine Cooling Fan. Manufacturer guidance describing normal cooling fan operation after engine shutdown and relevant safety precautions.
  7. HELLA Tech World. Engine Cooling and Cooling System Check. Technical guidance concerning coolant circulation, radiator operation, thermostats, water pumps, and cooling-system diagnosis.
  8. SAE International | Mobility, Advanced – SAE International

Radiator Fan Keeps Running A radiator fan that keeps running may be responding to engine temperature, A/C pressure, or an electrical control fault. Accurate diagnosis starts with the sensors, relays, and PCM commands.
Radiator Fan Keeps Running : A radiator fan that keeps running may be responding to engine temperature, A/C pressure, or an electrical control fault. Accurate diagnosis starts with the sensors, relays, and PCM commands.

#RadiatorFan #CoolingFanProblems #CarOverheating #CoolantTemperatureSensor #CoolingFanRelay #ACPressureSensor #AutoRepair #CarDiagnostics #OBD2 #EngineCoolingSystem #CarMaintenance #KoriScience


👉 Radiator Fan Keeps Running Read Next

If this article was helpful, you may also want to read the posts below.
They will help you understand the same topic in a broader and more practical way.

Radiator Cap Function and Failure Symptoms: Pressure Ratings, Testing & Replacement Cost

Clogged Radiator Symptoms: Idle vs Highway Overheating and Repair Costs

Car Radiator Structure: How Tubes and Fins Work, Leaks & Repair Costs

One new idea a day makes the world clearer.
See you in the next science story — KoriScience, Science with Wisdom.

댓글 남기기

광고 차단 알림

광고 클릭 제한을 초과하여 광고가 차단되었습니다.

단시간에 반복적인 광고 클릭은 시스템에 의해 감지되며, IP가 수집되어 사이트 관리자가 확인 가능합니다.